【资料名称】:告警7604的处理
【资料作者】:liujinzhong
【资料日期】:2011.7.20
【资料语言】:中文
【资料格式】:DOC
【资料目录和简介】:
告警7604的处理
一:告警原理:
主天线和分集天线之间的RX信号强度之差大于限定值(默认为10DB),告警产生。. 主天线和分集天线之间的RX信号计算强度之差至少比限定值低2DB,则可自动消除该告警。此现象反映在四代站为7604和7601;反映在三代站则为7949。
二:告警的书面解释:
1.四代站:7604 BTS OPERATION DEGRADED
Meaning
A major fault (or faults) has occurred in a unit (or units) that
belong to the sector indicated in the alarm.
Check the fault reason from the supplementary text field of the alarm.
Supplementary information fields
1-6XX XX XX XX XX XX
123456
1) rack (cabinet) number 4) type of unit
2) shelf number 5) unit number
3) slot6) subunit number
See the document Alarm Structure, Alarm Reference Manual
Instructions
All fault reasons
Instructions:
1.Check whether either of the following alarms is active:
7606 TRX FAULTY
7607 TRX OPERATION DEGRADED
and follow the instructions given for the active alarm(s).
Cancelling
This is a start/cancel type alarm. The alarm is cancelled automatically. Other fault reasons
2.三代站
7949 DIFFERENCE IN RX LEVELS OF MAIN AND DIVERSITY ANTENNA / TRX
Meaning
Difference of Rx signal strength between main and diversity
antennas is higher than the limit value (default 10 dB).
The BCF or OMU receives the limit value in BTS_CONF_DATA
message from the BSC. If the BSC does not send the value,
10 dB is used as a default value.
The Rx antenna monitoring is supported in Nokia 2nd generation,
Nokia Talk Family (all configurations with diversity) and
Nokia PrimeSite base stations.
Supplementary information fields
1-6XX XX XX XX XX XX
123456
1) rack (cabinet) number 4) type of unit
2) shelf number 5) unit number
3) slot6) subunit number
See the document Alarm Structure, Alarm Reference Manual.
Instructions
You cancel the alarm if the calculated Rx signal strength
difference between main and diversity antennas is at least
2 dB less than the limit value.
Cancelling
Do not cancel the alarm. The system cancels the alarm
automatically when the fault has been corrected.
三:我们总结的处理方式:
1.在基站用软件观察RSSI Comparision Values,若下图:
RSSI Comparision Values
***************************
Newest values:
TRX ID Ant 1Ant 2Ant 3Ant 4Diff.Rel. Diff.
---------------------------------------------------------------------
Sector 1
ETRX 1 -89-88n/an/a1-0.25
ETRX 2 -89-89n/an/a01.00
ETRX 3 -88-88n/an/a0-0.25
ETRX 4 -89-88n/an/a1-0.25
ETRX 5 -89-88n/an/a1-0.25
Avg. Diff.0.60
AntennaAnt:4Ant:3
ETRX 7 -86-860
ETRX 8 -88-880
ETRX 9 -87-870
Avg. Diff.0.00
大家注意到上图画面中的Diff值
理论上此值若大于10,告警出现。实际上此值若大于8,告警便会出现。我们的任务是在基站上将此值调到小于8:
检查思路
1).若Diff值大于10,查天馈线:
2).若Diff值小于10, 查接收合路器(M6LA,M2LA,RMUA):调整接收合路器接口或更换接收合路器 。
3).以上两种情况尚属较理想情况。 实际上我们还要进一步观察基站有无附加其他告警 。例如附加告警指向TRX,则更换 TRX,等。
处理方法:
一硬件方面:
1 核查天馈线顺序。确认扇区天馈是否接反并更正。
2 核查天馈质量。用sitemaster分别测主分集天馈系统务必使其驻波比在标准范围内且不要相差太多。
3.检查柜内射频跳线有无松动或损坏(锁紧螺母或更换坏跳线)。载频有无插到位(重新插拔)。架顶跳线及馈线各环节是否连通良好。这些因素都会诱发该告警。
4检查射频跳线顺序是否有错。
5. 通过环路测试或观察板件的新旧程度,优化板件位置。把性能相近的合路器及载频调整到同一个扇区。这一个方法更适合于DE34.
6.力求将性能较好的一根馈线用作主集收。
二软件方面:
1.如果室内覆盖基站仅有一根馈线连到我们的合路器上,对于四代站,仅仅修改基站硬件数据库是不够的,建议BSC数据上要去掉分集收。
2.如果某一扇区覆盖室外同时也做室内覆盖,那么主天线和分集天线之间的RX信号强度之差必然大于限定值(默认为10DB),告警必然产生。这时我们可以要求bsc将其主天线和分集天线之间的RX信号强度极限值更改为20以上。
3bsc数据有误:例如属于某小区内EGSM 之segment与另一小区segment做反了。这种现象在现场可以从站信息 site information 中观察出来。Bsc修改数据即可。
三 特殊情况(参考附件二):
如果确认各项测试正常,基站工作正常。且没有其他因素如干扰等影响。可以要求bsc将告警屏蔽。具体做法:要求bsc将其主天线和分集天线之间的RX信号强度极限值更改为20以上。
这只是我个人的一点看法,仅供参考。
2011/20/7
扫码关注5G通信官方公众号,免费领取以下5G精品资料
1、回复“iot6”免费领取《【8月30号登载】物联网创新技术与产业应用蓝皮书——物联网感知技术及系统应用》
2、回复“6G31”免费领取《基于云网融合的6G关键技术白皮书》
3、回复“IM6G”免费领取《6G典型场景和关键能力白皮书》
4、回复“SPN2”免费领取《中国移动SPN2.0技术白皮书》
5、回复“LTKJ7”免费领取《 联通科技周17本白皮书合集》
6、回复“5g-a”免费领取《中国联通5G-A 通感算融合技术白皮书》
7、回复“URLLC”免费领取《中国联通5G URLLC 技术白皮书》
8、回复“LDSL”免费领取《中国移动算力网络技术白皮书》
|