在5G网络中基于CSI-RS层三(L3)测量报告要求包括周期、事件触发的报告,它们分别要求如下:
周期报告
包含在周期性触发的测量报告中的报告的 CSI-RSRP、CSI-RSRQ 和 CSI-SINR 测量应满足第 10.1.4.2、10.1.5.2、10.1.9.2、10.1.10.2、10.1.14.2 和 10.1.15.2 节的要求。 .
事件触发的财期报告
包含在周期性触发的测量报告中的报告的 CSI-RSRP、CSI-RSRQ 和 CSI-SINR 测量应满足第 10.1.4.2、10.1.5.2、10.1.9.2、10.1.10.2、10.1.14.2 和 10.1.15.2 节的要求。 .
事件触发的周期性测量报告中的第一个报告应满足第 9.10.3.4.3 条规定的要求。
事件触发报告
包含在周期性触发的测量报告中的报告的 CSI-RSRP、CSI-RSRQ 和 CSI-SINR 测量应满足第 10.1.4.2、10.1.5.2、10.1.9.2、10.1.10.2、10.1.14.2 和 10.1.15.2 节的要求。 .
只要不满足报告标准,UE 不应发送任何事件触发的测量报告。
测量报告延迟定义为触发测量报告的事件与 UE 开始通过空中接口传输测量报告之间的时间。该要求假设测量报告不会被 DCCH 上的其他 RRC 信令延迟。该测量报告时延排除了在上行DCCH的TTI插入测量报告时产生的时延不确定性。延迟不确定度为:2 × TTIDCCH。该测量上报时延不包括UE没有上行资源发送测量上报的时延。
在没有 L3 过滤的情况下测量的事件触发的测量报告延迟应在第 10 节中定义的基于 CSI-RS 的测量范围内。当使用 L3 过滤时,可以预期额外的延迟。
具有测量间隙的频率间测量
当提供测量间隙时,如果配置了高层参数 CSI-RS-Resource-Mobility 和相关的 SSB,UE 应能够在 T CSI-RS_identify_inter 内识别新的基于可检测 CSI-RS 的频率间小区,
T CSI-RS_identify_inter = (TPSS/SSS_sync + T CSI-RS_measurement_period_inter + TCSI-RS_SFN_inter) ms
此处:
TPSS/SSS_sync 是 PSS/SSS 检测中使用的时间段,根据第 9.3.4 节中给出的 TPSS/SSS_sync_inter 和 TSSB_time_index_inter 确定,用于基于 SSB 的异频测量,
TCSI-RS_SFN_inter是用于获取被测小区SFN信息的时间段,FR1如表9.10.3.5-3所示,FR2等于9.3.4中的异频TSSB_time_index_inter,
TCSI-RS_measurement_period_inter:等于表9.10.3.5-1和表9.10.3.5-2中给出的基于CSI-RS的测量的测量周期。
Mmeas_period_inter:对于支持FR2功率等级1或5的UE,Mmeas_period_inter =8×N个样本。对于支持FR2功率等级2的UE,Mmeas_period_inter=5×N个样本。对于支持FR2功率等级3的UE,Mmeas_period_inter =5×N个样本。对于支持 FR2 功率等级 4 的 UE,Mmeas_period_inter = 5×N 个样本。请注意,比例因子 N = [8]。 CSSFinter:它是特定于载波的缩放因子,根据第 9.1.5 节中的 CSSFwithin_gap,i 确定,用于在测量间隙内进行的测量。
另外,对于给定的 CSI-RS 资源,如果关联的 SSB 被配置但未被 UE 检测到,或者如果 CSI-RS 配置了关联的 SSB 但没有 QCL-ed 到关联的 SSB,则不需要 UE 监控对应的 CSI-RS 资源。
Table 9.10.3.5-1: Measurement period for CSI-RS based inter-frequency measurements with gaps (Frequency FR1)
Condition NOTE1,2 | T CSI-RS_measurement_period_inter |
No DRX | Max(200ms, 8 ′ Max(MGRP, CSI-RS period)) ′ CSSFinter |
DRX cycle ≤ 320ms | Max(200ms, Ceil(8 ′ 1.5) ′ Max(MGRP, CSI-RS period, DRX cycle)) ′ CSSFinter |
DRX cycle > 320ms | 8 ′ DRX cycle ′ CSSFinter |
NOTE 1: DRX or non DRX requirements apply according to the conditions described in clause 3.6.1 NOTE 2: In EN-DC operation, the parameters, timers and scheduling requests referred to in clause 3.6.1 are for the secondary cell group. The DRX cycle is the DRX cycle of the secondary cell group. |
Table 9.10.3.5-2: Measurement period for CSI-RS based inter-frequency measurements with gaps (Frequency FR2)
Condition NOTE1,2 | T CSI-RS_measurement_period_inter |
No DRX | Max(400 ms, Mmeas_period_inter ′ Max(MGRP, CSI-RS period)) ′ CSSFinter |
DRX cycle ≤ 320ms | Max(400 ms, (1.5 ′ Mmeas_period_inter) ′ Max(MGRP, CSI-RS period, DRX cycle)) ′ CSSFinter |
DRX cycle > 320ms | Mmeas_period_inter ′ DRX cycle ′ CSSFinter |
NOTE 1: DRX or non DRX requirements apply according to the conditions described in clause 3.6.1 NOTE 2: In EN-DC operation, the parameters, timers and scheduling requests referred to in clause 3.6.1 are for the secondary cell group. The DRX cycle is the DRX cycle of the secondary cell group. |
Table 9.10.3.5-3: Time period for SFN acuisition for interfrequency CSI-RS based measurements with gaps(Frequency FR1)
Condition NOTE1,2 | T CSI-RS_SFN_inter |
No DRX | Max(200ms, [5] ′ Max(MGRP, SMTC period)) ′ CSSFinter |
DRX cycle ≤ 320ms | Max(200ms, Ceil([5] ′ 1.5) ′ Max(MGRP, SMTC period, DRX cycle)) ′ CSSFinter |
DRX cycle > 320ms | [5] ′ DRX cycle ′ CSSFinter |
NOTE 1: DRX or non DRX requirements apply according to the conditions described in clause 3.6.1 NOTE 2: In EN-DC operation, the parameters, timers and scheduling requests referred to in clause 3.6.1 are for the secondary cell group. The DRX cycle is the DRX cycle of the secondary cell group. |
资料来源:TS38.133 9.10
整理:kangguoying20211015