Gb over IP之后，可以使用 TERDI:RP=rp; 进入RP的调测模式。
平时接触的主要是 ifconfig; 和 ethif;
后来在其它的文档里还看到 APT GETCELLSTAT 等指令。
今天使用help; 看到里面还有很多其它的指令，有对这些指令了解的么？

Smon> :help;
he following commands has been reported:


?Prints syntax and a short explanation for each command
apt
catch
chiplist
connect
cpuload
create
delete
disable
disconnect
display
dump
echo
enable
errorlist
ethif
evlsendevent generation
evlviewview log events
file
flashprog
goto
gsi
halt
hdlc
helpPrints syntax and a short explanation for each command
ifconfig
keys
kill
mmu
monitor
no
olsconfig OLS timer configure command
pboot
pci
perf
ping
printfdRedirect standard out to this shell
program
rdshelp
read
reset
restart
route
rpbif
run
scope
segment
send
sequence
set
start
step
stop
sysinfo
tick
tip_icmp
trace
what
write
zzosvarp

For further information on a command type:
<command> ?


对于APT，使用 apt ?; 又有很多其它的指令，如下：
OSmon> :apt ?;
he apt command uses the RDS parser to access some parts
of the apt console. The RDS parser can be used with TERDI
from the MML command interface without extra debug equipment.

The following sub-commands are available:

getstat <proc>- Get APT debug counters
getcellstat [<cellId>] - Get APT debug counters for one cell
The cellId should be given in 3 digit hex
The cellId parameter should not be added
for process MP_MAC_<xxx> and RP_CHHCELL_<xxx>
clearstat <proc> - Reset APT debug counters
clearcellstat <proc>- Reset APT debug counters
per cell

frinfo <proc> <nsvcIndRp>- Get frame relay statistics
bssgpinfo <proc> - Get data from BSSGP
ldshbvcinfo <proc> <bvci>- Get BVCI data from Load Sharing
ldshcminfo <proc> - Get CM data from Load Sharing
ldshnsvcinfo <proc>- Get NSVCI data from Load Sharing
nscpinfo <proc>- Get data from NSCP

trace [long | all | clear] - Get logged error and trace messages
fastmedia [<yes>|<no>] - Switch off Mobile Logging
filter if using a fast media.
Used to indicate Ethernet LH.
radix [<hex>|<dec>]- Set radix mode for printouts

traceon <proc>- Enable additional tracing
traceoff <proc>- Disable additional tracing
gethelp <proc> [<command>] - RP Event Hand: Print help for a process or a command.
getunitreg <proc> - RP Event Hand: Get CM register status.
getegreg <proc>- RP Event Hand: Get registered Event Generators.
getegstate <proc> - RP Event Hand: Get state information for Event Generators.
getepreg <proc>- RP Event Hand: Get registered Event Proxies.

hangtbfindic <proc> [set |reset]- TBF Hanging indicator
ldmeas [ ? | <options>] - Load Measurmet help or tool options
melody [ ? | <options>] - Melody help or options

gb <on>|<off> [<options>]- GB Analyzer
gbfilter <on>|<off> <par>- GB Filter, see 'apt gbfilter ?'
setpar <proc><name><value> - Set Parameter in specified Process

printmsinfo <proc> [msind] - Get MS info.
printmslist <proc> [msind] - Get MS list.

ifconfig- Get IP configuration
gwsup - Get gateway supervision data
routelist- Get the routing list

debuglevel [? | <options>] - Change scope of log and debug functions
See help on subcommand for further info.

telneton- Enable Telnet
telnetoff- Disable Telnet

getevstat- Get RP Event data

gbip [? | <options>]- Get Gb over IP data
lr [? | <options>]- load regulation function help
ld [? | <options>]- load distribution function help
op [? | <options>]- overload protection function help
See help on subcommand for further info.

geteventinfo <proc>- Get RP Event Information

prof [? | <options>]- Code profiling

ncc [? | <options>]- Network Control function help
pgsl [? | <options>]- Packet GSL Information
con ? - Unit RGCONR debugger information

loadgen [? | <options>] - Load Generator